Replacement Brush Roll is #EB29027 Replacement Belt is the #EB29010 Replacement Swivel Neck is the #EB24019 Will not work on Ultra Soft Carpets. Click HERE for Ultra Soft Carpet Kit. Edge Cleaner Active brush edge cleaners are on both sides of the POWERHEAD electric brush. Guide either side of the brush along baseboards or next to furniture to help remove dirt trapped at carpet edges. Overload Protector The overload protector protects the motor from brush jamming and belt breakage. If the agitator slows down or stops, the overload protector shuts off the brush. To correct problem: Unplug the electrical cord, remove obstruction. Check brush area for excessive lint buildup or jamming. To reset: Press the reset button on top of the brush. Plug in the power cord, turn on vacuum and brush. Use with a Telescoping Wand (not included) The wand length is adjustable and requires no assembly. To adjust, simply push down on the wand adjust button and slide the upper wand to the desired height. The swivel, located on the POWERHEAD allows you to turn the handle to the left side to reach farther under low furniture. When raising the wand you may have to hold the POWERHEAD with your hand or foot. [toggle title=”Attach Wand” open=”no”] 1. To remove wands from the POWERHEAD, lock wands in straight-up position. 2. Press wand easy release pedal with foot and pull the wands straight up out of the POWERHEAD. The plug and cord do not have to be removed to use attachments on the wands. [/toggle] [toggle title=”Carpet Pile Indicator” open=”no”] Suggested pile height settings: For best deep down cleaning, use the XLO setting. However you may need to raise the height to make some jobs easier, such as scatter rugs and some deep pile carpets, and to prevent the vacuum cleaner from shutting off. As a general guide: XLO — most carpet heights LO — short to medium pile MED — medium to long pile HI — shag and long pile [/toggle] [toggle title=”Belt Changing and Agitator Cleaning” open=”no”] Disconnect cleaner from electrical outlet. Frequently check and remove hair, string and lint buildup in brush area. If buildup becomes excessive, disconnect the brush from wand and follow steps below. To Remove Belt: 1) Turn the POWERHEAD upside down. 2) Unscrew the brush cover screws. 3) Turn the POWERHEAD right side up. Press handle release pedal and lower the swivel. To remove cover, grasp the sides and pull out to release the outside of the cover. 4) Lift rear latches up and tilt cover forward from back until front snaps free. 5) Lift agitator assembly out, remove worn belt and clear any hair, string or lint build-up from brush area. [/toggle] [toggle title=”To Replace Belt:” open=”no”] 1) Install new belt over motor drive, then over brush sprocket. 2) Replace agitator assembly back into the POWERHEAD. 3) Line up front of cover and base. Rest cover on front edge of base as shown. 4) NOTE: On dirt sensor models be sure that the board is upright and the wires are tucked back as shown. 5) Tilt cover to back. Press cover firmly until side and rear tabs snap into place. Turn the POWERHEAD upside down and replace the 2 cover screws. [/toggle] [toggle title=”Changing the Light Bulb” open=”no”] 1) Remove the POWERHEAD cover as shown in BELT CHANGING AND AGITATOR CLEANING section. 2) Push in and turn bulb counterclockwise, then pull out to remove. 3) Push in and turn the bulb clockwise, to replace. Bulb must not be higher than 130 volts/15 Watts. 4) Reinstall the POWERHEAD cover as shown in BELT CHANGING AND AGITATOR CLEANING section. [/toggle] [toggle title=”Servicing the Agitator Brush” open=”no”] To Check Agitator Assembly: When brushes are worn to the level of the base support bars, replace the agitator assembly. To Replace Agitator Assembly: 1) Remove the POWERHEAD cover, belt and agitator assembly. See “To Remove Belt” in BELT CHANGING AND AGITATOR CLEANING. 2) Reinstall belt, new agitator assembly, and POWERHEAD cover. See “To Replace Belt” in BELT CHANGING AND AGITATOR CLEANING. [/toggle] [toggle title=”Parts List” open=”no”] 8 EB27008 SCREW 9 EB27009 MOTOR GASKET 10 EB29010 BELT 11 EB24011 MOTOR SPRING 12 EB29012 LOWER PLATE 13 EB29013 MOTOR 14 EB24014 MOTOR BRIDGE 15 EB29015 OVERLOAD PROTECTOR 16 EB21016 LIGHT BULB 17 EB29017 BULB SOCKET 18 EB24018 HANDLE RELEASE PEDAL 19 EB24019 SWIVEL *19 EB30019 SWIVEL 21 EB27021 WIRE CONNECTOR 22 EB24022 SWIVEL SEAL 23 EB29023 WHEEL 24 EB24024 PEDAL EASY RELEASE *24 EB30024 PEDAL EASY RELEASE 25 EB24025 REAR COVER *25 EB30025 REAR COVER 26 EB24026 FRONT AXLE ASSEMBLY 27 EB29027 AGITATOR BRUSH 28 EB27028 INDICATOR WINDOW 29 EB29029 LIGHT LENS 30 EB27030 EXHAUST FOAM 31 EB29031 WINDOW REFLECTOR 32 EB24032 CORD & PLUG ASSEMBLY *32 EB30032 LEAD WIRE UNIT 33 EB29033 REFLECTOR NOZZLE 34 EB29034 NOZZLE HOUSING (DECO) *34 EB31034 NOZZLE HOUSING (DECO) 35 EB27035 SWIVEL CAP 36 EB27036 CAM INDICATOR *37 EB30037 FRONT COVER *38 EB30038 PCB “B” UNIT *39 EB30039 SCREW *40 EB31040 PCB DIRT SENSOR 41 EB29041 LEAD WIRE 42 EB24042 INDICATOR LEVER 43 EB24043 PAD FOOT PEDAL 44 EB24044 INDICATOR BLOCK 45 EB24045 SPRING ASSIST *46 EB30046 WINDOW DIRT SENSOR 47 EB24047 LIFTER *48 EB30048 SCREW *49 EB31049 PCB SUPPORTER 50 EB27050 THRUST WASHER 51 EB27051 CATCH INDEXING 52 EB27052 WASHER 53 EB27053 RATCHET CATCH 54 EB27054 INDICATOR BLOCK ASSEMBLY 55 EB27055 SCREW [/toggle]
